CDR Railcar No. 10
-
- Trainee Driver
- Posts: 669
- Joined: Wed Sep 21, 2011 9:24 pm
- Location: kent england
Re: CDR Railcar No. 10
You have really done the railcar justice. Lots of us have a soft spot for the CDR railcars. It fits in perfectly on your line.
- Peter Butler
- Driver
- Posts: 5266
- Joined: Sun Sep 09, 2012 10:33 pm
- Location: West Wales
Re: CDR Railcar No. 10
What an absolute stunner, well done Rick, she is gorgeous and well worth the singed fingers!
The best things in life are free.... so why am I doing this?
Re: CDR Railcar No. 10
Brilliant job, Rik. Looks and runs very well and fits your line beautifully.
Philip
Re: CDR Railcar No. 10
Like most things, I see this as a learning experience. I'm not sure I've fully done the kit justice or yet quite perfected my soldering skills. The videos of master builders on YouTube make it look a lot easier than it turned out to be, particularly where access was tricky. Interestingly, the worst burn I got was picking up a blunt drill bit after trying to drill a hole..... !Peter Butler wrote: ↑Thu May 28, 2020 10:43 pm What an absolute stunner, well done Rick, she is gorgeous and well worth the singed fingers!
Rik
Re: CDR Railcar No. 10
Thanks chaps. I've always fancied having a CDR Railcar and No. 10 looked the most appropriate. The later ones look too slick for the PLR - though some of the early 4 wheelers look very attractive ......invicta280 wrote: ↑Thu May 28, 2020 10:41 pm You have really done the railcar justice. Lots of us have a soft spot for the CDR railcars. It fits in perfectly on your line.
Rik
- Tropic Blunder
- Trainee Fireman
- Posts: 189
- Joined: Sun Dec 06, 2015 4:02 am
- Location: Australia
- Contact:
Re: CDR Railcar No. 10
The railmotor looks good in service. The driver must be impressed with his new charge, as he is keeping it nice and clean.....
If the motor block you used under No. 10 is still available from the supplier, I'd be powering the railtruck. That way it can also be used on it's own for a bit of light shunting, or running light mixed trains on it's own.
From what I've read the motor unit of the railtruck was interchangeable with the motor unit of No. 10. It was sold without the motor to the CDJR and they are said to have used the cab to repair collision damage on No. 10. Looking at photos the only visible difference is a frame extension bolted on the back of the chassis to support the dropside body.
Like the railmotor, there is no visible cab door on either side, so presumably the driver had to clamber over the side of the truck portion to enter via the door in the back of the cab.........
Building the cab body work should be fairly easy in polystyrene, as you have the existing model to use as a pattern. The 'unit' as the CVR called it is a much simpler scratchbuilding proposition than a railmotor. Go for it!!
Regards,
Graeme
Re: CDR Railcar No. 10
Lovely job Rik, and thanks for the film - the finished thing looks VERY at home on your line, particularly with the wagons trailing along behind. You'll have to watch it or the management will want to scrap all those expensive and extravagant carriages and steam locos and just order a couple more of these...
Cheers,
Andrew.
Cheers,
Andrew.
Re: CDR Railcar No. 10
Pendle Valley Models do a generic bicycle in white metal for about £2.50, or you can splash out for a 1950s style gentleman's Raleigh cycle from Trenarren Models for £19.95! Given you now have the ability to print items, I suppose you will be better to try and find a pattern online to produce your own period cycle!
Phil
Sporadic Garden Railer who's inconsistencies know no bounds
My Line - https://gardenrails.org/forum/viewtopic ... 41&t=11077
Sporadic Garden Railer who's inconsistencies know no bounds
My Line - https://gardenrails.org/forum/viewtopic ... 41&t=11077
Re: CDR Railcar No. 10
Thanks. I think I'll resist the £20 job, but might be tempted by the £2.50 model, unless, as you say, I can find a decent 3d drawing.Lonsdaler wrote: ↑Fri Jun 05, 2020 12:06 pm Pendle Valley Models do a generic bicycle in white metal for about £2.50, or you can splash out for a 1950s style gentleman's Raleigh cycle from Trenarren Models for £19.95! Given you now have the ability to print items, I suppose you will be better to try and find a pattern online to produce your own period cycle!
Rik
Re: CDR Railcar No. 10
Let me know if you do Rik. I've looked a couple of times in the past without finding anything worth having.
Philip
- Old Man Aaron
- Trainee Driver
- Posts: 823
- Joined: Wed Oct 19, 2016 11:08 am
- Location: Sunshine Coast QLD, Australia
Re: CDR Railcar No. 10
Catching up again on this superb build. Suits your line perfectly, Rik.
Regards,
Aaron - Scum Class Works
Aaron - Scum Class Works
Re: CDR Railcar No. 10
Following my comment yesterday, being unable to get outside in today's weather, I had another trawl around for bike files and came up with this one on Thingiverse:
www.thingiverse.com/thing:4050110.
By reducing the drawings to 40% on the slicer it comes out at about 95mm long which is again about right for a 16mm bike. An hour or so printing and 20mins assembly of the half a dozen component pieces got me this ( in works grey and still needing a clean up.): The files are labelled in Dutch ( I think) and that would explain the front carrier which would be unusual on a UK mans bike. It actually comes with the file to print a crate to sit on the front, but after a 60% size reduction it was too flimsy to print properly and I think I'll take the front carrier off, a couple seconds with a scalpel should deal with that.
The only other detail which is missing are the chain sprockets, and they would be easy enough to make up from a piece of styrene.
www.thingiverse.com/thing:4050110.
By reducing the drawings to 40% on the slicer it comes out at about 95mm long which is again about right for a 16mm bike. An hour or so printing and 20mins assembly of the half a dozen component pieces got me this ( in works grey and still needing a clean up.): The files are labelled in Dutch ( I think) and that would explain the front carrier which would be unusual on a UK mans bike. It actually comes with the file to print a crate to sit on the front, but after a 60% size reduction it was too flimsy to print properly and I think I'll take the front carrier off, a couple seconds with a scalpel should deal with that.
The only other detail which is missing are the chain sprockets, and they would be easy enough to make up from a piece of styrene.
Philip
Re: CDR Railcar No. 10
Thanks Philip
I must give it a try. Not sure my printer will produce such a crisp finish but certainly worth a try.
Rik
I must give it a try. Not sure my printer will produce such a crisp finish but certainly worth a try.
Rik
Re: CDR Railcar No. 10
Rik,
Only after I printed and sprayed it and then posted, did I notice that it doesn't have a chain!!
I'm in the middle of trying to create that as an additional item, will let you know.
Only after I printed and sprayed it and then posted, did I notice that it doesn't have a chain!!
I'm in the middle of trying to create that as an additional item, will let you know.
Philip
Re: CDR Railcar No. 10
That looks an excellent representation of a period bicycle to me. As you say, a little work will give you the chainset.
Phil
Sporadic Garden Railer who's inconsistencies know no bounds
My Line - https://gardenrails.org/forum/viewtopic ... 41&t=11077
Sporadic Garden Railer who's inconsistencies know no bounds
My Line - https://gardenrails.org/forum/viewtopic ... 41&t=11077
Who is online
Users browsing this forum: No registered users and 1 guest